Foosball.com Forums

Chat Area => General Chat => Topic started by: FOOZUL on May 03, 2014, 03:44:10 PM

Title: Foosball parts available if interested!!!
Post by: FOOZUL on May 03, 2014, 03:44:10 PM

Looks like nobody cared for the Bonzini, no problem. Here are few items I'll
be listing on eBay an Craigslist soon, but just wanted to test the waters here.
Two sets of Fireball (dark rods) one set with players (black and silver) one set just the rods.
Got full set of Warrior players professionally rimmed for Tornado 5/8 rods.
Full set of Tornado Commercial grade rods (brand new).
8 Fireball Split bearings
Full set of Fireball rods (silver) with Tornado Players.
Full set of Warrior Players (blue and red era)  rimmed for Fireball rods.
Full set of German Lettner L4 16mm rods, best German Steel.
Full set of 22 Leonhart Counter balanced players with screws.


Peace

Title: Re: Foosball parts available if interested!!!
Post by: johnwallan on May 06, 2014, 12:13:18 AM

I don't mean to hijack...but I was wondering if the Fireball rods have the same spacing between the men as tornado.  Are the Fireball rods tougher than commercial tornado rods?

Title: Re: Foosball parts available if interested!!!
Post by: FOOZUL on May 06, 2014, 12:37:44 PM

Quote from: johnwallan on May 06, 2014, 12:13:18 AM

I don't mean to hijack...but I was wondering if the Fireball rods have the same spacing between the men as tornado.  Are the Fireball rods tougher than commercial tornado rods?

The spacing of the players are the same!!! The Fireball (black rods) heat treated rods are know to be on of the toughest rods ever made. Hope that helped.

Title: Re: Foosball parts available if interested!!!
Post by: heydude348 on May 29, 2014, 02:11:35 PM

Sorry for the off topic question but this is my first time on the site. Maybe you can help me with how to post a new question. Also, the question I am wondering about, How to change out a wood handle on a Tornado coin op? Any videos? Have read that cracking/splintering is a problem. Thanks for any help.

Title: Re: Foosball parts available if interested!!!
Post by: DenverFoosManiac on May 29, 2014, 02:50:02 PM

It was a learning experience for me. I have a few tips that could help you.

You must use the correct tool - http://www.amazon.com/Tornado-Foosball-Roll-Pin-Punch/dp/B001024X2S
Push the rod in as far as it will go
Use a rod support block (or something similar) to keep the rod in place
Turn the handle so one of the holes faces up
Hold the handle and Pin Punch with one hand and gently hammer with the other
If possible, use light taps throughout

When replacing the handles, follow the first three steps again, then:

Situate the handle on the rod
Guide the Pin Punch tool through the holes on the handle and rod to hold it in place
Spin the handle 180 degrees so the open hole faces up (the Pin Punch should stay in place)
Carefully center the Roll Pin over the open hole
Gently tap the Roll Pin into the handle until only 1/8" remains
Remove the Pin Punch (if it didn't fall out naturally)
Use the Pin Punch to tap the Roll Pin into position

I hope this helps you!

Title: Re: Foosball parts available if interested!!!
Post by: heydude348 on May 29, 2014, 04:24:00 PM

Thanks for the quick reply.I should have pointed out that I have had tables before but just wondering what type of support to use to prevent bending the rods.I also have the pin driver and extra parts.But thanks again for the reply.

Title: Re: Foosball parts available if interested!!!
Post by: DenverFoosManiac on May 29, 2014, 04:40:33 PM

I use one of these with a rag to prevent any table surface scratches.

(http://tornadofoosb.powweb.com/store/media/rodblock2.jpg)

Can be purchased at: http://tornadofoosb.powweb.com/store/page12.html

Title: Re: Foosball parts available if interested!!!
Post by: kman22 on June 18, 2014, 08:36:06 PM

Hey Foozul.
Im interested in talking to you about parts. HMU when you can and lets talk.